Latest Safety Projects

Categories

Nothing to show for Safety category yet. Here are some other projects that may interest you.

Building an Infrared Tracker with a PICAXE 14M2 and a Stepper Motor

Tracking an infrared light source is not as difficult as you might think; a 14-pin PICAXE, a stepper motor with a driver IC, three phototransistors, and a few other components will do the trick.

January 17, 2017 by Charles R. Hampton

Controlling a Servo with a PICAXE and an IR Sensor

A PICAXE 08M2 can be used to read the amount of IR (infrared) light falling on a phototransistor and respond by moving a servo to a predetermined position.

December 29, 2016 by Charles R. Hampton

Create a PID Controller on the NI myRIO—The Software

In this short project article series, we will implement a simple PID controller using LabVIEW on a hobby DC servo motor and the NI myRIO.

November 29, 2016 by Mark Narvidas

Make Your Own GPS Transmitter with the HC-12 Transceiver

Create a tracking device with an HC-12 transceiver, a GPS module, an Arduino, and Google Maps.

November 10, 2016 by Mark Hughes

Raspberry Pi Object Detection Cat Toy

This object detection toy will keep your cat's head spinning for hours!

November 07, 2016 by Ryan Jones

C-BISCUIT: Layout and Assembly for the Robot Control Board

We’ll discuss some important layout and manufacturing concepts as we look at the PCB for the Robot Control Board.

October 25, 2016 by Robert Keim

Build Your Own LED Saber—Assembly and Hilt Construction

In the final installment, we build our light-blade and assemble the electronics into the hilt.

October 21, 2016 by Jeremy Lee

Build Your Own LED Saber—Firmware, Microcontroller, and Testing

In part 3, we compile the firmware and build the controller at the heart of the Saber, then do initial testing and diagnostics.

October 20, 2016 by Jeremy Lee

C-BISCUIT: Schematic Design for the RCB—Power, Stepper

We’ll continue our discussion of the C-BISCUIT demo bot by looking at portions of the RCB schematic that weren’t covered in the previous article.

October 07, 2016 by Robert Keim

C-BISCUIT: Schematic Design for the RCB—Microcontroller, Motor Controller

In this article we’ll take a close look at two sections of the custom-designed control board for the C-BISCUIT demo bot.

September 21, 2016 by Robert Keim

Build an Arduino BLE-Enabled Indoor Air Quality Monitor

Use an Arduino/Genuino 101 with iAQ-Core air quality and HIH-6131 temperature/humidity sensors to make an Indoor Air Quality Monitor with Bluetooth low energy (BLE) connectivity.

September 16, 2016 by Raymond Genovese

Create a PID Controller on the NI myRIO—The Hardware

In this short project article series, we will implement a simple PID controller using LabVIEW with a hobby DC servo motor and NI myRIO.

September 12, 2016 by Mark Narvidas

C-BISCUIT: Robot System Architecture

The C-BISCUIT saga continues as we combine the various system components into a demo bot.

September 08, 2016 by Robert Keim

Build a Wireless “Tipping Bucket” Rain Gauge, Part 3—Receiver, PICAXE, and LCD

Here's a rain gauge that empties itself and that you can read from your easy chair. Best of all, you can build it, yourself.

August 19, 2016 by Charles R. Hampton

Build a Wireless “Tipping Bucket” Rain Gauge, Part 2—Adding the Transmitter

A tipping bucket rain gauge is a clever way to measure rainfall. Learn how to add wireless capability, a PICAXE microcontroller, and an LCD display to your weather station.

August 16, 2016 by Charles R. Hampton

Build a Wireless “Tipping Bucket” Rain Gauge, Part 1—Assembling the Bucket

A tipping bucket rain gauge, an RF transmitter and receiver, a PICAXE microcontroller, and an LCD can make a great addition to your weather station.

August 09, 2016 by Charles R. Hampton

Build Your Own RFID Technology Using an Arduino MEGA

In this article, we are going to learn some basics about RFID technology and use an Arduino MEGA to a play around with a popular RFID module, the ID12LA.

July 20, 2016 by Joseph Corleto

How to Build a Control Circuit with Adjustable Working Time via Wi-Fi

Learn how to build a system that can turn DC loads on and off using a mobile application. You'll also learn how to perform this task via immediate actions or via timers set in advance.

June 15, 2016 by Yahya Tawil

C-BISCUIT Power: Assembly and Testing of Regulator and Crowbar Circuits

Continuing the C-BISCUIT series, this article outlines how to populate and test the surface mount PCBs designed in a previous article using a hot air rework station and other various electronics tools.

May 31, 2016 by Patrick Lloyd

Create an Object Tracking System: Integrating Servo Control with Object Detect

This project covers integrating servo control and object detection.

May 10, 2016 by Michael Stock