This design solution evaluates the accuracy of thermocouples used for high-temperature measurements as well as resistance temperature detectors (RTDs) used for local cold-junction-compensation (CJC) points.
April 11, 2019 by Bonnie Baker, Maxim Integrated
This article offers an overview of the various component options for smart meter design and how they can improve the operation of the meters into which they are designed.
December 04, 2018 by Philippe Di Fulvio, Littelfuse Inc
Part 6 of this 12-part Resolving the Signal series focuses on output- versus input-referred noise, adding an amplifier at the input of an ADC, and low- versus high-resolution ADCs as they relate to amplifier noise.
June 19, 2018 by Bryan Lizon, Texas Instruments
Connected industrial machines can sense a wide array of information used to make key decisions within the Industrial Internet of Things (IIoT). A sensor within an edge node can be spatially far removed from any data aggregation point. It must connect through a gateway that links edge data with a network.
January 09, 2018 by Ian Beavers, Analog Devices
Part 1 of this two-part series discusses the key parameters and features a designer needs to be aware of and how they relate to inclination and stabilization applications, thus helping the designer choose the most suitable accelerometer.
December 12, 2017 by Chris Murphy, Analog Devices
Designing for the IoT comes with a unique set of challenges that require unique hardware solutions to overcome. Learn how smart passive sensors (SPSs)—sensors that function without a battery and without a microcontroller—are an example of IoT-specific design.
December 05, 2017 by ON Semiconductor
Integrated RF agile transceivers are not only widely employed in software-defined radio (SDR) architectures in cellular telephone base stations, such as multiservice distributed access system (MDAS) and small cell, but also for wireless HD video transmission for industrial, commercial, and military applications, such as unmanned aerial vehicles (UAVs).
November 07, 2017 by Wei Zhou, Analog Devices
In this multipart industrial IoT series, we will break down and explore the fundamental aspects of the edge node interpretation within the larger IoT framework: sensing, measuring, interpreting, and connecting data, with additional consideration for power management and security.
September 26, 2017 by Ian Beavers, Analog Devices
The industrial Internet of Things (IoT) encompasses the broad transformation underway that will make pervasive sensing across connected machines not just a competitive advantage, but an essential fundamental service. The industrial IoT starts with the edge node, which is the sensing and measurement entry point of interest.
September 12, 2017 by Ian Beavers, Analog Devices
This article looks at semiconductor technologies that are driving EV chargers, including high-voltage semiconductor switches, power converters, and multi-level complex power stages.
October 06, 2020 by Jayanth Rangaraju, Texas Instruments
This article looks at digit detection and recognition using MNIST eIQ as an example, which consists of several parts — the digit recognition is performed by a TensorFlow Lite model, and a GUI is used to increase the usability of the i.MX RT1060 device.
September 22, 2020 by David Piskula, NXP Semiconductors
In this article, we discuss some key security threats to be aware of when designing for the IoT, important security functions, and how protecting these designs is becoming easier with advances in security ICs.
September 15, 2020 by Scott Jones, Maxim Integrated
In this article, learn how to enable I2C by allowing the LPC55S69 MCU on the E1 board to communicate with a Bosch BME280 environmental sensor present on the Microe Weather click module.
September 10, 2020 by Mark Dunnett, on Behalf of NXP
Floating-gate Flash circuitry is only embedded in devices fabricated at 40nm or earlier nodes, so it is not embedded in the most advanced, highest-performance processors. For secure code and data storage, designers, therefore, have to specify an external device that contains secure memory capacity.
In partnership with Winbond
What are your assumptions about the reliability, longevity, and performance of NAND? This article proposes that embedded developers should open their minds to the potential benefits of replacing SPI NOR Flash with serial NAND Flash for storing mission-critical boot and application code.
In partnership with Winbond
MCAD and ECAD have inserted themselves into most design engineers' day-to-day work. Although familiar, both programs have come a long way and are continuing to evolve. In this article, learn the past and future of these design tools.
August 27, 2020 by Sam Sattel, Autodesk
Intel Enpirion PowerSoC modules are DC-DC step-down converters that integrate nearly all the components needed to build a power supply without sacrificing performance or efficiency. These solutions are designed to meet strict FPGA, ASIC, and processor power requirements.
August 25, 2020 by Tamara Lin, Intel
The OKdo E1 development board is only as wide as a coin but contains the LPC55S69 microcontroller, making it suitable for a variety of small production runs and prototypes. Here, get more familiar with the dev board and see how to use its evaluation kit.
August 20, 2020 by Mark Dunnett, on Behalf of NXP
Autonomous drones and robots utilize small motors. These fast-spinning mini motors require miniature encoders and IC package sizes. This article shows how an optical sinusoidal encoder provides a higher resolution and increased speeds with a 2x3 mm dual simultaneous-sampling SAR-ADC.
August 11, 2020 by Bonnie Baker, Maxim Integrated