In part 2 of the LED saber project, we'll assemble the power and audio systems.
In part 2 of the LED saber project, we'll assemble the power and audio systems.
An introduction to the Analog Discovery 2 by Digilent.
An introduction to the Analog Discovery 2 by Digilent.
In part one of this instrumentation and control (I & C) series, we'll go over the fundamental terminology and concepts…
In part one of this instrumentation and control (I & C) series, we'll go over the fundamental terminology and concepts used when working with industrial plants.
In this first part of a multi-part series, we will use a Tek MDO Mixed Domain Oscilloscope to illustrate options to…
In this first part of a multi-part series, we will use a Tek MDO Mixed Domain Oscilloscope to illustrate options to measure various circuit elements.
When inspecting electronic circuits, most measurements are displayed visually. This tool provides audible feedback to…
When inspecting electronic circuits, most measurements are displayed visually. This tool provides audible feedback to augment your analyses.
The mighty soldering iron. If you need one, want one, or just love to build stuff, then this project is for you.
The mighty soldering iron. If you need one, want one, or just love to build stuff, then this project is for you.
Learn how to build a device which senses when your computer monitor is physically rotated, and automatically tells your…
Learn how to build a device which senses when your computer monitor is physically rotated, and automatically tells your computer to rotate the display accordingly.
Learn how to read electrical signals and data from an analog device using the Step Response technique in Part 5 of the…
Learn how to read electrical signals and data from an analog device using the Step Response technique in Part 5 of the Building Raspberry Pi Controllers series.
Gather data via USB from a BH1745NUC optical sensor and then display color characteristics and illuminance values.
Gather data via USB from a BH1745NUC optical sensor and then display color characteristics and illuminance values.
In this continuing series of Building Raspberry Pi Controllers, you'll learn how to build a object detection control…
In this continuing series of Building Raspberry Pi Controllers, you'll learn how to build a object detection control circuit for operating a small DC motor using a photocell.
The intuitive, step-by-step procedure presented in this article will help you to successfully perform reflow soldering in…
The intuitive, step-by-step procedure presented in this article will help you to successfully perform reflow soldering in your toaster oven.
Take a few minutes to characterize a light dependent resistor (LDR) and you can build a simple and reasonably accurate…
Take a few minutes to characterize a light dependent resistor (LDR) and you can build a simple and reasonably accurate light meter can be built using an LDR and an Arduino.
In the last installment, we built the hardware to control an AC waveform with a TRIAC as the first step in a DIY solder…
In the last installment, we built the hardware to control an AC waveform with a TRIAC as the first step in a DIY solder reflow oven. This tutorial continues the project by showing you how to set up the low-level hardware to measure temperature, read the zero-cross detector, drive the TRIAC, and print to the serial terminal using a USART.
This article explains how to install PyVisa and MatPlotlib for Python. PyVisa connects a computer to the measurement…
This article explains how to install PyVisa and MatPlotlib for Python. PyVisa connects a computer to the measurement instruments and matplotlib helps to visualize the data collected from these instruments.
Use a laser and a photo resistor to build a laser based point-to-point communication system. The best part? It's under $10.
Use a laser and a photo resistor to build a laser based point-to-point communication system. The best part? It's under $10.
This project will show how to build a basic analog voltmeter using an Arduino Uno, LabVIEW software, and littleBits…
This project will show how to build a basic analog voltmeter using an Arduino Uno, LabVIEW software, and littleBits electronics modules.
In this article I will show you how to use the internal EEPROM of an ATMega 328P microcontroller. I will use a…
In this article I will show you how to use the internal EEPROM of an ATMega 328P microcontroller. I will use a USB-to-serial converter, and an LM35 temperature sensor. I will also give you some tips and tricks when designing a PCB.
Build your own TDR out of a scope and a signal generator to troubleshoot long cable runs and impedance mismatches.
Build your own TDR out of a scope and a signal generator to troubleshoot long cable runs and impedance mismatches.
This article describes in detail the connections necessary for two way communications between PICAXE microcontrollers and…
This article describes in detail the connections necessary for two way communications between PICAXE microcontrollers and personal computers. Both serial connections and USB to serial conversion connections are covered.
Learn how to use an EFM8 microcontroller to convert current and voltage measurements to digits that can be displayed on…
Learn how to use an EFM8 microcontroller to convert current and voltage measurements to digits that can be displayed on an LCD. We'll discuss a convenient way to report analog-to-digital conversion values that represent current and voltage amplitudes.
Facebook
Google
GitHub
Linkedin