The Sabertooth 2x32 motor controller can be used to create a robust drive platform for your next robotic endeavour. This article uses an Arduino Uno to…
The Sabertooth 2x32 motor controller can be used to create a robust drive platform for your next robotic endeavour. This article uses an Arduino Uno to communicate with the Sabertooth 2x32 controller.
Learn how to communicate between your PC and the SAM4S using the Atmel Software Framework’s USB module and simple ASCII…
Learn how to communicate between your PC and the SAM4S using the Atmel Software Framework’s USB module and simple ASCII commands.
Part One in this two-article series focuses on the hardware setup and on using a pulse-width-modulated signal to control a servo.
Part One in this two-article series focuses on the hardware setup and on using a pulse-width-modulated signal to control a servo.
No I2C interface with that sensor? No problem. Program a PIC chip as an I2C slave device for custom sensor and I/O…
No I2C interface with that sensor? No problem. Program a PIC chip as an I2C slave device for custom sensor and I/O interfacing. Here, we use three DHT22 sensors on a single I2C interface.
Tips and techniques for incorporating EFM8 microcontrollers into your custom hardware.
Tips and techniques for incorporating EFM8 microcontrollers into your custom hardware.
Learn how to measure distances up to 20 ft with a sonar sensor on an Arduino!
Learn how to measure distances up to 20 ft with a sonar sensor on an Arduino!
This article covers the essential characteristics and prominent advantages of the Inter–Integrated Circuit (aka I2C)…
This article covers the essential characteristics and prominent advantages of the Inter–Integrated Circuit (aka I2C) serial-communications protocol.
Got some time and need a wireless thermometer? In this article I'll show you how to make such a thing with a few PICAXEs.
Got some time and need a wireless thermometer? In this article I'll show you how to make such a thing with a few PICAXEs.
Getting more familiar with a PIC MCU is a matter of working more often with it. Learn how to make a wireless thermometer…
Getting more familiar with a PIC MCU is a matter of working more often with it. Learn how to make a wireless thermometer with a PIC microcontroller.
This handy introduction teaches you all about the RFM69HW transceiver module using two circuits running a wireless…
This handy introduction teaches you all about the RFM69HW transceiver module using two circuits running a wireless version of the "blinky" code.
Learn how to use a 433MHz RF module with an ATMega 328P-PU. In this article, we'll make a circuit with a DHT11 sensor and…
Learn how to use a 433MHz RF module with an ATMega 328P-PU. In this article, we'll make a circuit with a DHT11 sensor and a RF transmitter. We'll also make a receiving circuit with a 433MHz RF receiver and an LCD display.
Is IDT’s Tx/Rx wireless power solution suitable for applications that require high-precision analog performance?
Is IDT’s Tx/Rx wireless power solution suitable for applications that require high-precision analog performance?
This project will show how to build a basic analog voltmeter using an Arduino Uno, LabVIEW software, and littleBits…
This project will show how to build a basic analog voltmeter using an Arduino Uno, LabVIEW software, and littleBits electronics modules.
Create a wireless "relative comfort" light bar thermometer by broadcasting temperature data across multiple ESP8266…
Create a wireless "relative comfort" light bar thermometer by broadcasting temperature data across multiple ESP8266 modules running NodeMCU using MQTT.
How to add BLE capabilities to a wireless ceiling fan by incorporating the nRF51 in the remote control. Part of our…
How to add BLE capabilities to a wireless ceiling fan by incorporating the nRF51 in the remote control. Part of our series on the nRF51.
Part 4 introduces the readadc, select, case, and endselect PICAXE BASIC commands. It is the fourth article in a…
Part 4 introduces the readadc, select, case, and endselect PICAXE BASIC commands. It is the fourth article in a multi-part series on writing PICAXE code.
MQ Telemetry Transport (MQTT) is a popular low-overhead messaging protocol used by many IoT devices to communicate. This…
MQ Telemetry Transport (MQTT) is a popular low-overhead messaging protocol used by many IoT devices to communicate. This tutorial will show the user how to to set up a basic MQTT network using Python on his or her computer and an ESP8266 running the NodeMCU firmware.
Create a smart home by displaying the current salt level of your water softener with the CC3200 and a proximity sensor.
Create a smart home by displaying the current salt level of your water softener with the CC3200 and a proximity sensor.
Learn how to connect your device with Linux Screen using the built-in Lua interpreter to set up the file system and…
Learn how to connect your device with Linux Screen using the built-in Lua interpreter to set up the file system and connect to the network. Then, learn how to automate the scripting process with Luatool and put it all together with a basic TCP server that can interact with a pulse-width modulated LED, a potentiometer, and a switch.
A simple LCD control project with an EFM8 evaluation board demonstrates basic principles of embedded development.
A simple LCD control project with an EFM8 evaluation board demonstrates basic principles of embedded development.
Facebook
Google
GitHub
Linkedin