Latest Spectral Analysis Technical Articles

Categories

Intro Software Walkthrough: Fast Fourier Transforms and the Xilinx FFT IP Core

This article will explain some of the most important settings and design parameters for the Xilinx FFT IP core and function as a basic walkthrough of the Fast Fourier Transform interface.

October 17, 2018 by Steve Arar

Audio Processing in Scilab: How to Implement Spectrum Subtraction

This article discusses a technique in which frequency-domain subtraction is used to selectively suppress the noise components in an audio signal.

September 20, 2018 by Robert Keim

How to Use Scilab to Analyze Frequency-Modulated RF Signals

Computing a discrete Fourier transform can help you to analyze the ways in which RF modulation affects the spectrum of a carrier signal.

September 11, 2018 by Robert Keim

How to Use Scilab to Analyze Amplitude-Modulated RF Signals

Scilab’s FFT functionality can help you understand the frequency-domain effects of RF modulation techniques.

September 06, 2018 by Robert Keim

How to Perform Frequency-Domain Analysis with Scilab

In this article we’ll work with sinusoidal signals in the frequency domain using Scilab’s fast Fourier transform (FFT) functionality.

September 04, 2018 by Robert Keim

Resolving the Signal Part 7: The Effects of Amplifier Noise on Delta-Sigma ADCs

This 12-part article series focuses on the impact of noise in delta-sigma ADCs. Part 7 shows how to analyze different amplifiers' effect on the noise of the same ADC.

July 03, 2018 by Bryan Lizon, Texas Instruments

Basics of Digital Down-Conversion in DSP

This article discusses digital down-conversion which is a digital-signal-processing technique widely used in digital radio receivers.

June 04, 2018 by Steve Arar

How to Low-Pass Filter a Square Wave

This article, part of AAC’s Analog Circuit Collection, presents a circuit that is a good choice when you need to remove high-frequency noise from a digital signal.

March 07, 2018 by Robert Keim

Resolving the Signal: Introduction to Noise in Delta-Sigma ADCs Part 2

In part 2 of this series, I'll continue the fundamental ADC noise discussion by covering how to measure ADC noise, noise specifications in ADC data sheets, and absolute versus relative noise parameters.

February 13, 2018 by Bryan Lizon, Texas Instruments

Choosing the Most Suitable MEMS Accelerometer for Your Application: Part 2

In part 2 of this article, we will focus on key specifications and features in the context of wearable devices, condition monitoring, and IoT applications.

December 22, 2017 by Chris Murphy, Analog Devices

High-Speed Waveform Generation with an MCU and a DAC

In this article, we’ll evaluate different firmware strategies in our pursuit of maximum-frequency analog signal generation.

December 08, 2017 by Robert Keim

Fixed-Point Representation: The Q Format and Addition Examples

Fixed-point representation allows us to use fractional numbers on low-cost integer hardware.

November 30, 2017 by Steve Arar

Learn about the Overlap-Add Method: Linear Filtering Based on the Discrete Fourier Transform

The overlap-add method allows us to use the DFT-based method when calculating the convolution of very long sequences.

October 25, 2017 by Steve Arar

Ultrawideband DPD: The Rewards and Challenges of Implementation in Cable Distribution Systems

This article looks at new technologies regarding the existing cable network, in particular, power amplifier digital predistortion.

October 24, 2017 by Patrick Pratt, Analog Devices

Linear Filtering Based on the Discrete Fourier Transform

The DFT provides an efficient way to calculate the time-domain convolution of two signals.

October 19, 2017 by Steve Arar

The Effect of Coefficient Quantization on the Performance of a Digital Filter

This article will verify that a suitable structure can reduce the sensitivity of a digital filter response to the coefficient quantization.

October 12, 2017 by Steve Arar

Design of FIR Filters Using the Frequency Sampling Method

This article will review the basics of the frequency sampling method for designing FIR filters.

September 29, 2017 by Steve Arar

Intelligence at the Edge Part 2: Reduced Time to Insight

In this multipart industrial IoT series, we will break down and explore the fundamental aspects of the edge node interpretation within the larger IoT framework: sensing, measuring, interpreting, and connecting data, with additional consideration for power management and security.

September 26, 2017 by Ian Beavers, Analog Devices

How to Use a Robot to Record and Transfer Audio Signals

This article provides detailed information on sampling audio signals and transferring the data to a PC for analysis.

September 15, 2017 by Robert Keim

An Introduction to the Fast Fourier Transform

This article will review the basics of the decimation-in-time FFT algorithms.

August 28, 2017 by Steve Arar